Related Topics
  • No related Topics found

PACKED BED REACTOR SYSTEM STUDY ON THE BIOSORPTION OF Cr (VI) FROM AQUEOUS SOLUTION USING CORN COB POWDER


Content

ABSTRACT

 

 

The current method used in the treatment of Cr(VI) uses biosorbents that are expensive hence the need for cheaper available biosorbent. In this study,potential use of corn cob powder biomass, as a bioremediation agent for the removal of Cr(VI) was investigated in a packed bed column bioreactor. The effects of the operating parameters such as influent Cr(VI) concentration, pH, biomass concentration, flow rate and temperature, on the Cr(VI) removal were investigated in the continuous system using a packed-bed reactor. Percentage removal curves were obtained for different flow rate, pH, temperature, biomass concentration and initial concentration of Cr(VI). It was found that the adsorption of Cr(VI) to the biomass was strongly dependent on these parameters, as expected. In particular, the influent pH and temperature were most significantly affected leading toa high percentage removal of Cr(VI); a decrease in the influent pH of 2, and an increase in the temperature up to 70°C enhanced the Cr(VI) reduction in the column significantly (P<0.05) up to 70 ± 11.39 %. A flow rate of 5min/ml was optimum for higher removal percentage. FTIR spectra analysis carried out on the biosorbent showed the presence of some functional group; hydroxyl (OH), carboxylic (COOH), ethyne (CH), and ethane (CH2) groups which are responsible for the biosorption reaction in the column. Both Langmuir and Freundlich adsorption isotherms fitted reasonably well with

 

the data and showed high correlation coefficient (R2) values of 0.993 and 0.985 respectively. These results show that, the adsorbent can be used as a low cost alternative in biosorption of wastewaters containing lowerconcentrations of Cr(VI).Finally, the potential of the column packed with corncobbiomass for Cr(VI) detoxification has been

 

 

 

 


found to be a good biosorbent in removal of Cr(VI) from aqueous solutions and also in

 

the treatment of Cr(VI) containing industrial waste

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 


TABLE OF CONTENT

 

Title Page

Abstract

Table of Content

List of Abbreviations

 

CHAPTER ONE: INTRODUCTION

1.1       Background of Study

1.2       Statement of Research Problem

1.3       Justification

1.4       Aims and Objectives

1.4.1    Aims

1.4.2    Specific Objectives

 

CHAPTER TWO: LITERATURE REVIEW

2.1       Biosorption

2.1.1    Mechanism of Biosorption

2.1.2    Factors Affecting Biosorption

2.1.3    Advantages of Biosorption

2.2       History of Corn

2.2.1    Classification of Corn

2.2.2   Biosorbent Properties of Corncob

2.3       Chemistry and Characteristic of Chromium

2.4       Hexavalent Chromium

2.4.1    Toxicity of Chromium (VI)

2.4.2   Chromium (VI) andthe Environment

2.4.3   Health Hazards of Chromium (VI)

2.5       Packed Bed Column Reactor

2.5.1   Benefits of Continuous Reactors

2.6       The Adsorption Isotherm of Metal Removal

2.6.1    Freundlich Adsorption Study

2.6.2    Langmuir Adsorption Study

 

CHAPTER THREE: MATERIALS AND METHODS

3.1       Materials

3.1.1    Biosorbent

3.1.2   Reagents and Equipment Used

3.1.3    Continuous Reactor System

3.2       Methods

3.2.1    Pre-Treatment of Biosorbent

3.2.2   Preparation of Chromium (VI) Solution

3.2.3   Preparation of DiphenylCarbazideSolution (Developing Reagent)

3.2.4   Determination of Chromium (VI) Concentration

3.2.5   Preparation of Standard Curve

3.2.6   Determination of the Effect of Mass of Biosorbent on Chromium (VI) Removal

3.2.7    Determination of the Effect of Flow Rate on Chromium (VI) Removal

3.2.8    Determination of the Effect of Temperature on Chromium (VI) Removal

3.2.9    Determination of the Effect of Initial K2Cr2O7 Concentration on Chromium (VI) Removal

3.3.0    Determination of the Effect of pH on Chromium (VI) Removal

3.3.1    The Use of Activated Carbon as Adsorbent For Chromium (VI) Removal

3.3.2    The Used of Waste Water Containing Chromium(VI) from a Leather Tanning Industry

3.3.3   FTIR Analysis of Biosorbent

3.3.4    Statistical Analysis

 

CHAPTER FOUR: RESULTS

4.1       Effect of Mass of Corncob on Chromium (VI) Removal

4.2       Effect of Flow Rate on Chromium (VI) Removal

4. 3      Effect of Temperature on Chromium (VI) Removal

4.4       Effect of Initial K2Cr2O7 Concentration on Chromium(VI) Removal

4.5       Effect of pH On Chromium (VI) Removal

4.6       Use of Activated Carbon as aAdsorbent In The Column

4.7       The Used of Waste Water Containing Chromium(VI) from NILEST

4.8       FTIR Analysis of Biosorbent

4.9       The Adsorption Isotherm Studies

 

CHAPTER FIVE: DISCUSSION

 

CHAPTER SIX: SUMMARY, CONCLUSION AND RECOMMEMDATION

6.1       Summary

6.2       Conclusion

6.3       Recommendation

REFERNCES

APPENDICES


LIST OF ABBREVIATION

 

 

ANOVA                                         Analysis of Variance

 

 

FTIR                                                                                Fourier Transform Infrared Spectroscopy

 

 

KBr                                                                                 Potassium Bromate

 

 

NARICT                                                                       National Research Institute for Chemical

 

Technology

 

 

NILEST                                                                        National Institute of Leather Science and

 

Technology

 

 

pH                                                                                    Potential of Hydrogen Ions

 

 

PAC                                                                                Powdered Activated Carbon

 

 

SD                                                                                    Standard Deviation

 

 

SPSS                                                                                Statistical Package for the Social Science

 

 

WHO                                                                              World Health Organization

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 


 

CHAPTER ONE

 

 

INTRODUCTION

 

 

1.1              Background of Study

 

Over the last three decades there has been increasing global concern over the public health impacts attributed to environmental pollution. The World Health Organization (WHO)estimates that about a quarter of the diseases facing mankind today occur due to prolonged exposure to environmental pollution (WHO, 2002).

 

Pollution by heavy metals is one of the serious environmental threats as a result of various industrial discharges (Wang and Chen, 2009). Hexavalent chromium Cr (VI) is released into the environment by many industrial activities such as leather tanning, chrome plating, stainless steel welding, pigment production and nuclear weapon production (Gonzalez et al., 2003). Chromium exists in two oxidation states Cr(III) and Cr(VI), and the most toxic form is Cr(VI), which has been implicated in causation of liver damage, pulmonary congestion and oedema (Babu and Gupta, 2008; Raji and Anirudhan, 1998).

 

Pollution of water due to presence of certain heavy metal ions is a severe socio-environmental problem caused by the discharge of industrial wastewater. In view of their toxicity, non-biodegradability and persistent nature, their removal becomes an

 

absolute necessity. However, such processes are not only expensive and highly energy intensive, but also lead to production of harmful by-products and end-products, the ultimate disposal of which again causes secondary pollution (Sen and Ghosh, 2010).

 

1


 

Rapid industrialization and urbanization have resulted in increased discharge of heavy metals such as lead, chromium, mercury, selenium, zinc, arsenic, gold, silver, copper, nickel, etc. into aquatic ecosystem which has become a matter of concern over the last few decades due to pollutant’s, carcinogenic and mutagenic nature(Ayres, 1992). These toxic materials are generated during mining operation, refining ores, sludge disposal, fly ash from incinerators, and the process of radioactive metal plating or the manufacture of electrical materials, metal equipment, paints, alloys, batteries, pesticides or preservatives (Trivedi, 1989).The untreated effluent from electroplating industries contains approximately 100mg/L chromium (VI) which is much higher than the permissible limit of 0.05-1mg/L (Deilippis and Pallaghy, 1994).

 

The process of removing heavy metal by a biological material is known as Biosorption and the biological materials used are called biosorbents. Several methods have been employed in the removal of heavy metals and other contaminants.Biological processes (biosorption, bioaccumulation and biodegradation) have been proposed as potential methods for the removal of heavy metals from the environment. However, bioaccumulation and biodegradation have been linked with some disadvantages such as resistance to microbial activity, production of by-product and/or other metabolites with higher toxicity than primary substrate (Ramsay and Nguyen, 2002). Thus, biosorption is considered to be one of the promising processes for removing hazardous and environmentally undesirable chemicals (Hu et al., 2010). Mohantyet al. (2005) showed some of the advantages of biosorption method, which include removal of both organic and inorganic constituents even at very low concentrations, its relative ease and safe to operate, usage of both batch and continuous equipment with no sludge formation, and the

 

2


adsorbent can be regenerated and reused.

 

 

Various biosorbents like bacteria, fungi, yeast, agricultural by product, industrial wastes, etc. have been used for biosorption (Gadd, 1993). Biosorption of toxic metals is based on a non-enzymatic process such as adsorption. Adsorption is due to the non-specific binding of ionic species to cell surface associated or extracellular polysaccharides or proteins (Volesky, 1990). Bacterial cell wall, the polysaccharides and proteins present in the corn cob powder are efficient metal biosorbent that bind charged group.

 

The use of biosorption technology using granular and powdered activated carbon has been carried out. However, prohibitive costs limit their extensive utilization especially in developing countries. Because of growing interest, the low-cost, easily available and environment friendly agricultural residues have been tested as metal biosorbents and a number of agro-based plant waste materials, such as papaya wood (Saeedet al., 2005), and rice husk (Tarley and Arruda, 2004), coconut fibers (Espinolaet al., 1999) black gram husk (Saeed and Iqbal, 2003) have been reported as potential biosorbents.

 

 

This report focuses on the investigation of the potential of corn cob also known asZea mays cob for the removal of chromium VI ions from aqueous solution. The polysaccharides and protein present in Zea mays cob were reported to be efficient metal biosorbent that bind to the charged group of these toxic metal. (Gibson and Benson, 2002).

 

The abundance of corn cob in most developing countries as well as its composition and cost effectiveness make it a strong candidate to be used as an adsorbent for removal

 

 

3


 

of many pollutants from aqueous solutions. The current economic values of corn cob are less than the apparent cost of collection, transportation and processing for beneficial use (Tsai et al., 2001). Thus, corn cob has been used as fertilizer and soil conditioners by land application, as animal and poultry bedding, as fiber and roughage in animal feed (Bagby and Widstrom, 1987) and as energy source by combustion (Lin et al., 1995). However, direct utilization of corn cob as metal biosorbent may be economical, practical and useful.Thus thisstudy aims at exploring the feasibility of using corn cob as an adsorbent for the uptake ofChromium (VI) from aqueous solution. Also, the effects of various factors including pH, contact time, temperature and adsorption isotherms on the uptake will be investigated.

 

1.2              Statement of Research Problem

 

Chromium is one of the major pollutants in the environment and is frequently present in wastewaters from various industrial units. Chromium is a toxic metal of widespread use and it exists in several oxidation states. Among the several oxidation states, Cr (VI) is considered to be the most toxic. It is usually associated with oxygen as chromate (Cr042-) or dichromate (Cr072-) ions. The Hexavalent form of chromium is considered to be a group “A” human carcinogen because of its mutagenic and carcinogenic properties (Helmer and Bartley, 1971). The untreated effluent from electroplating industries contains approximately 100mg/L chromium (VI) which is much higher than the permissible limit of 0.05-1mg/L (Deilippis and Pallaghy, 1994).

 

The persistent nature of Cr (VI) makes it accumulate in the food chain which with time reaches harmful levels in living beings resulting in serious health hazards such as irritation in lungs and

 

stomach, cancer in digestive tract, low growth rates in plants and death of animals(Park et al.,

 

4


 

2004). Therefore, removal of Cr(VI) from wastewater, prior to its discharge into natural water systems, adjoining landmasses and sewer systems, requires serious and immediate attention. The contaminated corn cob powder can now be properly disposed in such a way as to prevent it from being introduce into natural waters and accumulating in the food chain. Also, it can be recycled and channeled into other means of chemical production.

 

1.3              Justification

 

Corn is a staple food in the northern part of Nigeria; it is produced in large quantity which leads to the availability of corn cobs in large quantity that could always be put into use.It contains cellulose and hemicelluloses, which have adsorption and biosorption properties; hence can bind to Cr(VI) ions. Corn cobs are common wastes found in our environment; hence can help convert waste into useful form. Cr(VI) adsorption has been carried out using other biosorbent e.g. Neem saw dust (Vinodhini and Nilanjana, 2009) hence the need to investigate the ability of corn cob powder in adsorption of Cr( VI) is imperative. Continuous reactors are generally able to cope with much higher reactant concentrations due to their superior heat transfer capacities(Jameset al., 1975). Continuous reactors make higher mixing rates possible. The output from a continuous reactor can be altered by varying the run time. This increases operating flexibility for manufacturers.Despite the demonstration of the efficiency of corncob to bioremediateCr (VI) using batch process (Sallauet al., 2012), there is no information of the biosorption of Cr(VI) using corn cob in a continuous process. Therefore, this study may create a method that will assist industries in reducing toxicity of waste water containing Cr (VI).

 

1.4              Aim and Objectives

 

1.4.1        Aim

 

5


 

The aim of this study was to examine the potential of corncob powder in the biosorption of chromium (VI) in aqueous solution in a continuous bioreactor process.

 

1.4.2        Specific Objectives

 

The specific objectives of this study are:

 

I.            To investigate the effect of some operating parameters such as mass of corn powder, flow rate, influent solution pH and temperature on chromium (VI) removal by corn cob powder in the column

 

II.            To compare the absorptive properties of corncob powder with activated carbon, a standard synthetic adsorbent used in industries

 

III.           To compare the potentials of corncob powder in removal of chromium (VI) from synthetic chromium (VI) Solution and industrial waste containing chromium (VI).

 

IV.       To carry out Fourier transform infrared spectroscopy (FTIR) of the biosorbent

 

before and after biosorption

 

 

V.            To carry out adsorptionisotherm studies of the biosorption process.

Order Complete Project